technical data in74ac241 octal 3-state noninverting buffer/line driver/line receiver high-speed silicon-gate cmos ordering information IN74AC241N plastic in74ac241dw soic t a = -40 to 85 c for all packages the in74ac241 is identical in pinout to the ls/als241, hc/hct241. the device inputs are compatible with standard cmos outputs; with pullup resistors, they are compatible with ls/als outputs. this octal noninverting buffer/line dr iver/line receiver is designed to be used with 3-state memory address drivers, clock drivers, and other bus-oriented systems. the device has noninverting outputs and two output enables. enable a is active-low and enable b is active-high. ? outputs directly interf ace to cmos, nmos, and ttl ? operating voltage range: 2.0 to 6.0 v ? low input current: 1.0 a; 0.1 a @ 25 c ? high noise immunity characteristic of cmos devices ? outputs source/sink 24 ma logic diagram pin 20=v cc pin 10 = gnd function table inputs output inputs output enable a a ya enable b b yb l l l h l l l h h h h h h x z l x z x = don?t care z = high impedance pin assignment rev. 00
in74ac241 rev. 00 maximum ratings * symbol parameter value unit v cc dc supply voltage (referenced to gnd) -0.5 to +7.0 v v in dc input voltage (referenced to gnd) -0.5 to v cc +0.5 v v out dc output voltage (referenced to gnd) -0.5 to v cc +0.5 v i in dc input current, per pin 20 ma i out dc output sink/source current, per pin 50 ma i cc dc supply current, v cc and gnd pins 50 ma p d power dissipation in still air, plastic dip+ soic package+ 750 500 mw tstg storage temperature -65 to +150 c t l lead temperature, 1 mm from case for 10 seconds (plastic dip or soic package) 260 c * maximum ratings are those values beyond which damage to the device may occur. functional operation should be restricted to the reco mmended operating conditions. +derating - plastic dip: - 10 mw/ c from 65 to 125 c soic package: : - 7 mw/ c from 65 to 125 c recommended operating conditions symbol parameter min max unit v cc dc supply voltage (referenced to gnd) 2.0 6.0 v v in , v out dc input voltage, output voltage (referenced to gnd) 0 v cc v t j junction temperature (pdip) 140 c t a operating temperature, all package types -40 +85 c i oh output current - high -24 ma i ol output current - low 24 ma t r , t f input rise and fall time * (except schmitt inputs) v cc =3.0 v v cc =4.5 v v cc =5.5 v 0 0 0 150 40 25 ns/v * v in from 30% to 70% v cc this device contains protection circuitry to guard agains t damage due to high static voltages or electric fields. however, precautions must be taken to avoid applications of any voltage highe r than maximum rated voltages to this high-impedance circuit. for proper operation, v in and v out should be constrained to the range gnd (v in or v out ) v cc . unused inputs must always be tied to an appropriate logic voltage level (e.g., either gnd or v cc ). unused outputs must be left open.
in74ac241 rev. 00 dc electrical characteristics (voltages referenced to gnd) v cc guaranteed limits symbol parameter test conditions v 25 c -40 c to 85 c unit v ih minimum high- level input voltage v out = v cc -0.1 v 3.0 4.5 5.5 2.1 3.15 3.85 2.1 3.15 3.85 v v il maximum low - level input voltage v out = 0.1 v 3.0 4.5 5.5 0.9 1.35 1.65 0.9 1.35 1.65 v v oh minimum high- level output voltage i out -50 a 3.0 4.5 5.5 2.9 4.4 5.4 2.9 4.4 5.4 v * v in = v ih i oh =-12 ma i oh =-24 ma i oh =-24 ma 3.0 4.5 5.5 2.56 3.86 4.86 2.46 3.76 4.76 v ol maximum low- level output voltage i out 50 a 3.0 4.5 5.5 0.1 0.1 0.1 0.1 0.1 0.1 v * v in =v il i ol =12 ma i ol =24 ma i ol =24 ma 3.0 4.5 5.5 0.36 0.36 0.36 0.44 0.44 0.44 i in maximum input leakage current v in =v cc or gnd 5.5 0.1 1.0 a i oz maximum three- state leakage current v in (oe)= v ih or v il v in =v cc or gnd v out =v cc or gnd 5.5 0.5 5.0 a i old +minimum dynamic output current v old =1.65 v max 5.5 75 ma i ohd +minimum dynamic output current v ohd =3.85 v min 5.5 -75 ma i cc maximum quiescent supply current (per package) v in =v cc or gnd 5.5 8.0 80 a * all outputs loaded; thresholds on input associated with output under test. +maximum test duration 2.0 ms, one output loaded at a time. note: i in and i cc @ 3.0 v are guaranteed to be less than or equal to the respective limit @ 5.5 v v cc
in74ac241 ac electrical characteristics (c l =50pf, input t r =t f =3.0 ns) v cc * guaranteed limits symbol parameter v 25 c -40 c to 85 c unit min max min max t plh propagation delay, a to ya or b to yb (figure 1) 3.3 5.0 1.5 1.5 9.0 7.0 1.5 1.0 10.0 7.5 ns t phl propagation delay, a to ya or b to yb (figure 1) 3.3 5.0 1.5 1.5 9.0 7.0 1.0 1.0 10.5 7.5 ns t pzh propagation delay, output enable to ya or yb (figure 2) 3.3 5.0 1.5 1.5 12.5 9.0 1.0 1.0 13.0 9.5 ns t pzl propagation delay, output enable to ya or yb (figure 2) 3.3 5.0 1.5 1.5 12.0 9.0 1.5 1.0 13.0 9.5 ns t phz propagation delay, output enable to ya or yb (figure 2) 3.3 5.0 2.0 1.5 12.0 10.0 2.0 1.0 12.5 10.5 ns t plz propagation delay, output enable to ya or yb (figure 2) 3.3 5.0 1.5 1.5 12.5 10.0 1.0 1.0 13.5 10.5 ns c maximum input capacitance 5.0 4.5 4.5 pf in rev. 00 typical @25 c,v cc =5.0 v c power dissipation capacitance 45 pf pd * voltage range 3.3 v is 3.3 v 0.3 v voltage range 5.0 v is 5.0 v 0.5 v figure 1. switching waveforms figure 2. switching waveforms
in74ac241 n suffix plastic dip (ms - 001ad) symbol min max a 24.89 26.92 b 6.1 7.11 c 5.33 d 0.36 0.56 f 1.14 1.78 g h j 0 10 k 2.92 3.81 notes: l 7.62 8.26 1. dimensions ?a?, ?b? do not include mold flash or protrusions. m 0.2 0.36 maximum mold flas h or protrus ions 0.25 mm (0.010) per s ide. n 0.38 d suffix soic (ms - 013ac) symbol min max a 12.6 13 b 7.4 7.6 c 2.35 2.65 d 0.33 0.51 f 0.4 1.27 g h notes: j 0 8 1. dimensions a and b do not include mold flash or protrusion. k 0.1 0.3 2. maximum mold flash or protrusion 0.15 mm (0.006) per side m 0.23 0.32 for a; for b ? 0.25 mm (0.010) per s ide. p 10 10.65 r 0.25 0.75 dimens ion, mm 1.27 9.53 dimens ion, mm 2.54 7.62 a b h c k c m j f m p g d r x 45 seating plane 0.25 (0.010) m t -t- 1 20 10 11 l h m j a b f g d seating plane n k 0.25 (0.010) m t -t- c 1 20 10 11 rev. 00
|